Shanghai Rotorcomp Screw Compressor Co., Ltd.
  • Drehschraube Kompressor Historischer bekannter Hersteller, der Qualität Schraubenkompressor, ölfreier Kompressor, Hochdruckverdichter in ISO, TUV, CE-Zertifikate mit gutem Preis, 5 Jahre Garantie, patentiertes, einzigartiges Design, mehr energiesparendes, zuverlässiges Kompresso Drehschraube Kompressor
  • Ölfreier Kompressor Shanghai Rotor-Kompressor-Kompressor bieten 100% sauberen Öl-freien Luft-Kompressor, die in luftgekühlt und wassergekühlt werden können, können wir nach den speziellen Anfragen und OEM-Service ... Ölfreier Kompressor
  • Luftbehandlungssysteme Nachbearbeitungsgeräte von KompressorISO, CE, TUV, ASME Standardhersteller, der Qualität herstellt Kaltlufttrockner, Trockenlufttrockner, Präzisionsrohrfilter von 1mikron bis 0,001Mikron, Aktivkar ... Luftbehandlungssysteme
  • Diesel beweglicher Schraubenkompressor Diesel beweglicher SchraubenkompressorReliable Diesel-beweglicher Schraubenverdichterhersteller, der Qualitäts-Dieselschraubenkompressor von 50cfm - 1600cfm @ 100psi-500psi in ISO, TUV, CER-Beschein ... Diesel beweglicher Schraubenkompressor
  • Schraube Air End SCREW AIR ENDWorld-top Rotorcomp kompakte Luftschraube Kompressor mit bester Effizienz in kleineren Demension in ISO, TUV Zertifikate, 5 Jahre Garantie.Rotorcomp Öl-Injektion Schraube Luftenden schaffen das Herz ... Schraube Air End
CONATCT
Tel: + 86-021-67150020
Fax: + 86-021-67150020
Hinzufügen: Nr.28 Minta Straße, Songjiang Bezirk Shanghai, China
code

Fehlerbehebung

Fehlerbehebung
· Im Betrieb einer Anomalie, bitte nicht ignorieren die Ursachen des Phänomens sollte identifiziert werden und
Angemessene Behandlung
· Um das Ereignis des Ausfalls auszuschließen, lesen Sie bitte sorgfältig und verstehen Sie die Verwendung von Broschüren.
· Vollständig verstehen, die Struktur und Funktion der Maschine sind der Schlüssel zur Früherkennung der Störung.
· Dieses Kapitel dokumentiert in erster Linie gemeinsame Fehler, Ursachen und Behandlung. Es gibt keine Unterlassung, aber nicht
Dokumentiert den ganzen Fehler und seine Behandlung. Abgesehen von der Störung wurde dokumentiert und Behandlungsmethoden,
Bitte Bediener und Wartungspersonal selbst sorgfältig darauf achten, dass Maschinen ordnungsgemäß laufen.

FEHLERSUCHE

Malfunction

Possible Causes

Solution

The compressor cannot start.

1. The fuse is burnt.

2. Malfunction of start-up of electrical equipment.

3. Ill connection of start-up of a button.

4. Ill connection of the circuit.

5. Voltage is too low.

6. Malfunction of the motor.

7. Malfunction of air end. (Abnormal noise and feel part of the air end too hot.)

8. Lack phases of power supply.

9. Overload of fan motor.

Ask a qualified electrician for overhaul and replacement.

Running current is high. The compressor stops by itself.

(Alarm due to excessive hot of Air end )

1. Voltage is too low.

2. Discharge pressure is too high.

3. Jam of oil-air separator core.

4. Malfunction of air end.

5. Malfunction of circuit.

1. Ask electrician for overhaul.

2. Check/regulate pressure parameters.

3. Replace with new pats.

4. Disassembly, examine and repair.

5. Ask electrician for overhaul.


Discharge temperature is lower than normal level.

1. Invalidation of thermostatic valve.

2. A long time in vacancy of ON.

3. Invalidation of discharge temperature sensor.

4. Invalidation of suction valve, suction inlet does not open fully.

1. Examine, repair and clean or replace valve core.

2. Increase air consumption.

3. Examine and replace.

4. Clean and replace.


Discharge temperature is too high to stop the compressor automatically

1. Lack of Lubricate condensate.

2. Wrong type and Spec. of lubricate condensate.

3. Jam of oil filter.

4. Jam or heavy dirt of oil cooler.

5. Malfunction of the thermostatic sensor.

6. Invalidation of thermostatic valve.

7. Too many dust accumulate in the fan and cooler.

8. Motor of fan doesn’t work.


1. Inspect and supplement href="#_ftn1" [1]  lubricate condensate.

2. Replace with new condensate according to requirements.

3. Use new subassemblies.

4. Examine and clean.

5. Use new subassemblies.

6.Examine, clean, replace with new subassemblies

7. Disassemble and clean, blow off and dry

8. Examine circuit and motor of fan.

Discharge too much oil in compressed air

1. Core of oil-air separator broken.

2. Jam of valve.

3. Too much lubricating condensate.

1. Use new subassemblies.

2. Clean the valve.

3. Discharge part of oil.

Air flow is below normal level.

1. Jam of air filter.

2. Jam of oil-air separator core.

3. Blowby of electromagnetic valve.

4. Leakage of the pipeline.

5. Belts skid and loose.

6. Suction valve cannot be open fully.

1. Remove impurities or use new subassemblies.

2. Use new subassemblies.

3. Clean out or use new subassemblies.

4. Examine and repair.

5. Use new subassemblies and tighten belts.

6. Clean out or use new subassemblies.

Oil return from the air filter after stop.

Invalidation of spring or sealed ring is broken.

Replace broken subassemblies.

Safety valve puff away.

1. Safety valve runs too long.

2. Invalidation of pressure control and working pressure is too high.

1. Use new subassemblies or regulate again.

2. Examine or regulate it again.

  • TEL:+ 86-021-67150020
  • FAX:+ 86-021-67150020
  • EMAIL:Sales@rotorcompressor.com
  • ADDRESS:Nr.28 Minta Straße, Songjiang Bezirk Shanghai, China